Forums

Help › Forums

Re: Using the Pitch/Chip shot mode - putting green grid.

Mon, Dec 29 2014 11:07 AM (95 replies)
  • MainzMan
    9,591 Posts
    Wed, May 7 2014 12:33 AM

    Will a hearty hand shake do?

    : ))

    andyson:

         

    Why does the one second from the left have no face?  I know things can get a bit rough round here but pulling someone's face off seems a bit extreme.

  • DaddysKat
    3,554 Posts
    Wed, May 7 2014 12:41 AM

    MainzMan:
    Will a hearty hand shake do?

    Only if you throw in a Laurel, Mainz!  Ya know ... a Laurel ... and hearty handshake!

    I'm so punny!  lol.

    MainzMan:
    Why does the one second from the left have no face?  I know things can get a bit rough round here but pulling someone's face off seems a bit extreme.

    That's me, Mainz ... I'm the one that dances to a different drummer here!

  • keidan
    311 Posts
    Fri, Dec 26 2014 10:26 AM

    DaddysKat:

    MainzMan:
    Will a hearty hand shake do?

    Only if you throw in a Laurel, Mainz!  Ya know ... a Laurel ... and hearty handshake!

    I'm so punny!  lol.

    MainzMan:
    Why does the one second from the left have no face?  I know things can get a bit rough round here but pulling someone's face off seems a bit extreme.

    That's me, Mainz ... I'm the one that dances to a different drummer here!

     

    Maybe just facing a different direction (: 

    Sooo...  20 ft, 24 ft, 26 ft or 10 yds for that pesky grid?  or maybe size was settled in another thread?

  • borntobesting
    9,706 Posts
    Mon, Dec 29 2014 10:34 AM

    keidan:
    Sooo...  20 ft, 24 ft, 26 ft or 10 yds for that pesky grid?  or maybe size was settled in another thread?

    If you just use the 13 full sized squares the grid is 26 feet X 26 feet. I ignore the partial squares on each side and figure it as 26 feet X 26 feet. If You use the 2 partial squares then it is 30 feet X 30 feet . But the partial squares  aren't always the same size so it just makes sense to me to go 26 feet X 26 feet. 

  • keidan
    311 Posts
    Mon, Dec 29 2014 10:56 AM

    borntobesting:

    keidan:
    Sooo...  20 ft, 24 ft, 26 ft or 10 yds for that pesky grid?  or maybe size was settled in another thread?

    If you just use the 13 full sized squares the grid is 26 feet X 26 feet. I ignore the partial squares on each side and figure it as 26 feet X 26 feet. If You use the 2 partial squares then it is 30 feet X 30 feet . But the partial squares  aren't always the same size so it just makes sense to me to go 26 feet X 26 feet. 

    Thanks BTB that makes a lot of sense.  I imagine that there is still a small error bar even for your approach given the widely different POV distances and sampling used but this should be plenty good for wind calcs where error bars for wind/equipment are much larger.  -Keith 

  • borntobesting
    9,706 Posts
    Mon, Dec 29 2014 11:07 AM

    keidan:

    borntobesting:

    keidan:
    Sooo...  20 ft, 24 ft, 26 ft or 10 yds for that pesky grid?  or maybe size was settled in another thread?

    If you just use the 13 full sized squares the grid is 26 feet X 26 feet. I ignore the partial squares on each side and figure it as 26 feet X 26 feet. If You use the 2 partial squares then it is 30 feet X 30 feet . But the partial squares  aren't always the same size so it just makes sense to me to go 26 feet X 26 feet. 

    Thanks BTB that makes a lot of sense.  I imagine that there is still a small error bar even for your approach given the widely different POV distances and sampling used but this should be plenty good for wind calcs where error bars for wind/equipment are much larger.  -Keith 

    Keep in mind that each square is 2 feet by 2 feet and it helps. 

RSS